ARTNET protocol MADRIX light show software ,KTV stage control system, H802RA four-port LED controller

Controller introduction:

1.H802RA adopts standard Ethernet protocol, support Art-Net protocol

2.Four output port,can control a number of LED driver chip,support automatically edit address function.

3.The input network port can be directly connected to the computer network card,  the offline ,online main control, and  the switch and the photoelectric converter.

4.When online , the supporting software is “LED Studio Software” or “MADRIX”, and the offline supporting software is “LED Programming Software”.

Supporting driver chips:

> DMX512, HDMX；

> LPD6803, LPD8806, LPD1882, LPD1889, LPD1883, LPD1886；

> TM1812, TM1809, TM1804, TM1803, TM512, TM1926, TM1913, TM1914, TM1814；

> UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, UCS512, UCS8904；

> APA102, APA104, P9813, WS2801, WS2803, WS2811, WS2812, WS2821, SM16716, SM16711,

> INK1003, LX1003, MY9221, MBI6021, MBI6024, LD1510, LD1512, LD1530, LD1532,ect.

> UCS8904 controls more 3200points ，and the other chips  control more 4096points.

MY9221, UCS8904, MBI6024 is 65536 grayscale ，LPD1886 is 4096 grayscale，MBI6021 is 1024 grayscale，LD15XX is only control 256 grayscale mode.

Performance characteristics：

1.Four output port,multi-control 4096 pixels,each port control 1024 points.

2.Supporting Art-Net protocol,and it can match MADRIX software.

3. The DMX chip of Tianwei and Lianxinke can be addressed.

4.Available “LED studio software ” set to repeater and amplifier.

5.Linkable and detachable, can directly connect to the computer  online card,and also can linked to the offline and online master.

6.Flexible to use,sub-control can be arbitrary exchanged ,strong adaptability to lighting engineering.

7.Long transmission distance ,transmission signal adopt the Ethernet protocol,nominal distance is 100 meter.

8.Sub-controller can be used as a relay,can be directly  converted into modules by photoelectric,make the transmission distance more than 25 kilo meters .

Setup steps:

Connection diagram:

1.Connect to the computer online,supporting software is LED radio software or Madrix.

2.Offline connection to the main control, SD card control, and the supporting software is LED programming software.

Note: Between the main control and the sub-controller, between the computer and the sub-controller, and between the adjacent sub-controllers, use a crossover network cable to connect.

Indicator status：

1.Green light flashes：network port has date input.

2.Red light flashes :four network ports has date output .

Red light not flashes: no electric.

Port definition:

>Wiring definition for each port(from top to bottom):GND, CLK, DAT, D-, D+

>Two-wire driver chip connection：GND  CLK  DAT

> DMX512 lamp connection：GND  D-  D+，to single-line addressing，addressing wire connectionCLK

> General single-wire driver chip connection GND DAT

> Speial TM1926, TM1913, TM1914, TM1814 connection ：GND D+

Specifications:

Input voltage                            AC110V or 220V(customizable)

Rated power consumption    1.3W

Load points                              4096point

Peoduct weight                        1KG

Operating temperature          -40C°–85C°

Dimensions     L163 x W155 x H54 / Bare board size L119 x W47 x H21

Carton size       L205 x W168 x H69